Big Block FordInstallation Manual For Systems with A/C#14600 / #14620Billet Specialties, Inc.500 Shawmut Avenue.La Grange, Illinois 60526Tech Line (70
www.billetspecialties.comFigure 5: Prepping The Tensioner(A) Apply anti-seize to one end of 5/16-18 x 1” socket set screw and thread into back of tens
www.billetspecialties.comFigure 6: Install Bridge BracketApply anti seize to three 5/16-18 x 1” flat head cap screws, one 5/16-18 x 1-1/2” flat head
www.billetspecialties.comFigure 7: Install The A/C CompressorApply anti seize to the compressor shoulder bolt and to two 8mm-1.25 x 25mm ARP 12pt. cap
www.billetspecialties.comFigure 8: Install The AlternatorApply anti seize to one 10mm-1.5 x 100mm ARP 12pt cap screw and one 8mm-1.25 x 25mm 12pt. cap
www.billetspecialties.comFigure 9: Install Power Steering PumpInstall one 5/16” split washer to each of the two 5/16-18 x 2-3/4” socket head cap screw
www.billetspecialties.com15Figure 10: Install Damper & Crank Pulley(A) Install Damper and spacer on crank per OEM specifications.Place a 3/8” Bell
www.billetspecialties.comFigure 11: Install Water Pump Pulley & A/C Compressor Clutch CoverWater Pump PulleyApply anti seize to four 5/16-24 x 3/4
www.billetspecialties.comFigure 12: Install Idler PulleysApply anti seize to three 3/8-16 x 1-3/4” ARP 12pt. cap screws. Thread a 3/8-16 x 1-3/4” ARP
www.billetspecialties.comFigure 13: Install A/C Compressor ManifoldImportant! • Only remove sealed cap on compressor if you plan on charging you’re A/
www.billetspecialties.comFigure 14: Install Belt & Tensioner Pulley(A) Install and route belt as shown in the diagram below allowing belt to rest
PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLING ANY COMPONENTS OF THE TRU TRAC SERPENTINE SYSTEMIMPORTANT: VEHICLE OIL PAN MUST BE REMOVED FOR INSTALLA
Billet Specialties, Inc.500 Shawmut AvenueLa Grange, Illinois 60526Tech Line 708.588.0505Fax 708.588.7181www.billetspecialties.com#14600/ #14620
Required Tools & MaterialsAnti-seize CompoundRTV SiliconePermatex Hylomar® gasket dress-ingGasket ScraperScotch-Brite® Pad5/16-18 Thread Chaser* &
Skin Board #3 - Packaged In Main Box8mm-1.25 x 25mm 12pt. Cap ScrewBridge Bracket To Alternator & CompressorTensioner Pulleyx33/8-16 x 3/4” 12pt.
Other Hardware / GasketsGoodyear Poly-V Serpentine Belt - 70.50” #4050705 (with power steering)Goodyear Poly-V Serpentine Belt - 57.75” #4065078 (wi
www.billetspecialties.comFigure 1: Prepping The BlockDisconnect battery; remove all existing accessory drive brackets and components from motor. Remov
www.billetspecialties.comFigure 2: Prepare & Install Timing Cover(A) Install oil pan end seal into timing cover with a thin bead of RTV silicone (
(A)(B)(C)(D)Figure 3a: Prepare Water Pump For Installation(A) Install supplied water pump to manifold nipple and (B) heater hose barbed fitting or blo
www.billetspecialties.comFigure 3b: Install Water PumpApply anti-seize to the five 5/16-18 x 1-1/2” ARP 12pt. cap screws and RTV Sealer to the two 5/1
Comments to this Manuals