HEMI / BB ChryslerInstallation Manual For Systems with A/C#14800 / #14820Billet Specialties, Inc.500 Shawmut Avenue.La Grange, Illinois 60526Tech Line
www.billetspecialties.comFigure 5: Install The Bridge BracketFor kits with power steering: Attach the power steering support bracket to the back of th
www.billetspecialties.comFigure 6: Install AlternatorApply anti-seize to the M10 x 2-3/4” ARP 12pt cap screw, place and align the alternator between t
www.billetspecialties.comFigure 7: Install The A/C CompressorApply anti-seize to the compressor shoulder bolt threads. Attach the SD-7 compressor to t
www.billetspecialties.comFigure 8: Install The Tensioner(A) Apply anti-seize to the threads of the 5/16-18 x 1” set screw and thread into the back of
www.billetspecialties.comFigure 9: Install Power Steering Pump & PulleyApply anti-seize to the two 5/16-18 x 2-3/4” socket head cap screws and to
www.billetspecialties.comFigure 10: Install Crankshaft & Water Pump PulleysCrankshaft Pulley: Place crank pulley on damper and align holes. Apply
www.billetspecialties.comFigure 11: Install Idler PulleysApply anti-seize to the three 3/8-16 x 1-3/4” ARP 12pt cap screws. Thread the 3/8-16 x 1-3/4”
www.billetspecialties.comFigure 12: Install A/C Compressor Clutch CoverApply Loctite Blue 242 to the following:(3) 1/4-20 x 3/4” socket head cap screw
www.billetspecialties.comFigure 13: Install A/C Compressor ManifoldImportant! • Only remove sealed cap on compressor if you plan on charging you’re A/
www.billetspecialties.comFigure 14: Install Belt & Tensioner Pulley(A) Install and route belt as shown in the diagram below allowing belt to rest
PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLING ANY COMPONENTS OF THE TRU TRAC SERPENTINE SYSTEMIMPORTANT: Must use thin crank vibration damper Mopar P
Billet Specialties, Inc.500 Shawmut AvenueLa Grange, Illinois 60526Tech Line 708.588.0505Fax 708.588.7181www.billetspecialties.com#14800/ #14820
Required Tools & MaterialsAnti-seize CompoundRTV SiliconePermatex Hylomar® gasket dress-ingGasket ScraperScotch-Brite® Pad3/8-16 Thread Chaser* &a
Skin Board #3 - Packaged In Main Box8mm-1.25 x 25mm 12pt. Cap Screwx33/8-16 x 3/4” 12pt. Cap Screwx13/8-16 x 1-3/4” 12pt. Cap Screwx310mm-1.5 x 70mm 1
Other Hardware / GasketsGoodyear Poly-V Serpentine Belt - 74.75” #4060747 (with power steering)Goodyear Poly-V Serpentine Belt - 65.00” #4060650 (wi
www.billetspecialties.comFigure 1: Prepping The BlockDisconnect battery; remove all existing accessory drive brackets and components from motor. Remov
www.billetspecialties.comFigure 2: Install Water Pump Housing & PumpApply Permatex Hylomar® gasket dressing to both sides of water pump housing ga
www.billetspecialties.comFigure 3: Install The A/C BracketPlace A/C bracket (14806)on passenger side of water pump housing and align with the two left
www.billetspecialties.comFigure 4: Install The Alternator BracketFor kits without power steering continue to Step 2.Step 1: Attach the power steering
Comments to this Manuals